硬盤分區并不復雜,，只要你按照下面的圖示步步為營,，很快就能學會的,！
　首先你需要利用軟盤或光盤啟動盤啟動計算機,，下圖是軟盤啟動后得到的畫面：

Your computer has a disk larger than 512 MB. This version of Windows

Includes Improved support for large disks, resulting in More efficient

use of disk space on large drives, and allowing disks over 2GB to be

畫面大意是說磁盤容量已經超過了512M,，為了充分發揮磁盤的性能,，建議選用FAT32文件系統，輸入“Y”鍵后按回車鍵,。
　　現在已經進入了Fdisk的主畫面,，里面的選項雖然不多，但選項下面還有選項,，操作時注意別搞混了,。

FDISK Options

Current fixed disk drive: 1

Choose one of the following:

1. Create DOS partition or Logical DOS Drive

2. Set active partition

3. Delete partition or Logical DOS Drive

4. Display partition information

Enter choice:[1]

Press Esc to exit FDISK
　　圖中選項解釋：
　　1、創建DOS分區或邏輯驅動器
　　2,、設置活動分區
　　3,、刪除分區或邏輯驅動器
　　4、顯示分區信息
　　接下來將講解如何創建新分區,，請關注下篇,。
接上篇，選擇“1”后按回車鍵,，畫面顯示如下：

Create DOS Partition or Logical DOS Drive

Current fixed disk drive:1

Choose one of the following:

1.↙Create Primary DOS Partition

2.  Create Extended DOS Partition

3.  Create Logical DOS Drive(s) in the Extended DOS Partition

Enter choice: [1]
　　圖中釋義：
　　1,、創建主分區　　2、創建擴展分區　　3,、創建邏輯分區
　　一般說來,，硬盤分區遵循 著“主分區→擴展分區→邏輯分區”的次序原則，而刪除分區則與之相反,。一個硬盤可以劃分多個主分區,，但沒必要劃分那么多，一個足矣,。主分區之外的硬盤空間就是擴展分區,，而邏輯分區是對擴展分區再行劃分得到的。
　　一,、創建主分區（Primary Partition）
　　選擇“1”后回車確認,，Fdisk開始檢測硬盤……

Create Primary DOS Partition

Current fixed disk drive:1

Verifying drive integrity, 11% complete. -

　　你是否希望將整個硬盤空間作為主分區并激活,？主分區一般就是C盤，隨著硬盤容量的日益增大,，很少有人硬盤只分一個區,，所以按“N”并按回車。

Create Primary DOS Partition

Current fixed disk drive:1

Do you wish to use the maximum available size for a Primary DOS Partition

and make the partition active (Y/N)……………………?[Y]

顯示硬盤總空間,，并繼續檢測硬盤……

Create Primary DOS Partition

Current fixed disk drive:1

Total disk space is 51151 Mbytes (1 Mbytes = 1048576 bytes)

Verfying drive integrity, 15% complete. –

設置主分區的容量,，可直接輸入分區大小（以MB為單位）或分區所占硬盤容量的百分比（%）,，回車確認,。

Create Primary DOS Partition

Current fixed disk drive:1

Total disk space is 51151 Mbytes (1 Mbytes = 1048576 bytes)

Maximum space available for partition is 51151 Mbytes (100%)

Enter partition size in Mbytes or percent of disk space (%) to

create a Partition……………………………………………………[51151]主分區C盤已經創建，按ESC鍵繼續操作,。

Create Primary DOS Partition

Current fixed disk drive:1

Partition  Status  Type  Volume  Label  Mbytes  System  Usage

C: 1                PRI DOS              3030   UNKNOWN    6%

Primary DOS Partition created

Press Esc to continue –

二,、創建擴展分區（Extended Partition）
　　回復至Fdisk主菜單，選擇“1”繼續操作,。

FDISK Options

Current fixed disk drive : 1

Choose one of the following :

1.Create DOS partition or Logical DOS Drive

2.Set active partition

3.Delete partition or Logical DOS Drive

4.Display partition information

Enter choice : [1]

WARNING ! No partitions are set active – disk 1 is not startable unless

Press Esc to exit FDISK

這一步選“2”,，開始創建擴展分區。

Create DOS Partition or Logical DOS Drive

Current fixed disk drive:1

Choose one the following:

1. Create Primary DOS Partition

2. Create Extended DOS Partition

3. Create Logical DOS Drive(s) in the Extended DOS Partition

Enter choice:[2]
　　硬盤檢驗中,，稍候……

Create Extended DOS Partition

Current fixed disk drive:1

Partition  Status  Type  Volume  Label  Mbytes  System  Usage

C:1            PRI DOS                3030   UNRNOWN     6%

Verifying drive integrity   9% complete
　　習慣上我們會將除主分區之外的所有空間劃為擴展分區,，直接按回車即可。當然,，如果你想安裝微軟之外的操作系統,，則可根據需要輸入擴展分區的空間大小或百分比。

Create Extended DOS Partition

Current fixed disk drive:1

Partition  Status  Type  Volume  Label  Mbytes  System  Usage

C:1           PRI DOS             3030     UNLNOWN      65

Total disk space is 51151 Mbytes (1 Mbyte = 1048576 bytes)

Maximum space  available for partition is 48195 Mbytes ( 94% )

Enter partition size in Mbytes or percent of disk space (5) to

create an Extended DOS Partition………………………:[48195]

擴展分區創建成功,！按ESC鍵繼續操作。

Create Extended DOS Partition

Current fixed disk drive:1

Partition  Status  Type  Volume  Label  Mbytes  System  Usage

C: 1             PRI DOS               3030   UNRFNOWN     6%

2             FXT DOS              48195   UNRFNOWN     94%

Extended DOS Partition created
三,、創建邏輯分區（Logical Drives）
　　畫面提示沒有任何邏輯分區,，接下來的任務就是創建邏輯分區。

Create  Logical  DOS  Drive(s)  in the  Extended  DOS Partition

NO logical drives defined

Verifying drive integrity, 16% complete. –

前面提過邏輯分區在擴展分區中劃分,，在此輸入第一個邏輯分區的大小或 百分比,，最高不超過擴展分區的大小。

Create Logical DOS Drive (s) the Extended DOS Partition

No logical drives defined

Total Extended DOS Partition size is 48195  Mbytes (1 Mbyte =1048576 bytes)

Maximum space available for logical drive is 48195 Mbytes (100%)

Enter logical drive size in Mbytes or percent of disk space (%)…[48195]
　　邏輯分區D已經創建,。

Create Logical DOS Drive（s）in the Extended DOS Partition

Drv Volume Label Mbytes System Usage

D:               5005   UNKNOWN    10%

Verifying drive integrity,     9% complete.

Logical DOS Drive created , drive letters changed or added
　　如法炮制,，繼續創建邏輯分區。

Create Logical DOS Drive(s) in the Extended DOS Partition

Drv Volume Label Mbytes System Usage

D:               5005   UNKNOWN    10%

Total EXTENDED dos Partition size is 48195 Mbyte (1 Mbyte = 1048576 bytes)

Maximum space available for logical drive is 43190 Mbytes ( 90%)

Enter logical drive size in Mbytes or percent of disk space (%)…[43190]

Logical DOS Drive created , drive letters changed or added

Press Esc to return FDISK Options
　　邏輯分區E已經創建,，按ESC返回,。

Drv Volume Label Mbytes System Usage

D:             5005 UNKNOWN     10%

E:           43190  UNKNOWN     90%

All available space in the Extended DOS Partition

is assigned to logical drives.

Press Esc to continue-
　　當然，你還可以創建更多的邏輯分區,，一切由你自己決定,。

　四,、設置活動分區（Set Active Partition）
　　又回復至主菜單，選“2”設置活動分區,。

FDISK Options

Current fixed disk drive：1

Choose one of the following:

1.Create DOS partition or Logical DOS Drive

2.Set active partition

3.Dekete partition or Logical DOS Drive

4.Display partition information

Enter choise:[2]

WARNING,！No partitions are set active –disk 1 is not startable unless

a  partition is set active
　　只有主分區才可以被設置為活動分區！
　　選擇數字“ 1”,，即設C盤為活動分區,。當硬盤劃分了多個主分區后，可設其中任一個為活動分區,。

Set Active Partition

Current fixed disk drive:1

Partition Status Type Volume Label Mbytes System Usage

C:1              PRI DOS            3004   UNKNOWN        6%

2              EXT DOS           48195    UNKNOWN       94%

Total the space is 51199 Mbytes (1 Mbytes = 1848576 bytes )

Enter the number of the partition you want to make to the active …………:[1]
　　C盤已經成為活動分區,，按ESC鍵繼續。

Set Active Partition

Current fixed disk drive:1

Partition Status Type Volume Label Mbytes System Usage

C:1          A   PRI DOS            3004   UNKNOWN   6%

2              EXT DOS           48195   UNKNOWN   94%

Total disk space is 51199 Mbytes (1 Mbytes = 1848576 bytes )

Partition 1 made active
　　五,、注意事項
　　必須重新啟動計算機,，這樣分區才能夠生效；重啟后必須格式化硬盤的每個分區,，這樣分區才能夠使用,。

You MUST restart your system for your changes to take effect.

Any drives you have crated or changed must be formatted

AFTER you restart.

Shut down Windows before restarting.
六、刪除分區
　　如果你打算對一塊硬盤重新分區,，那么你首先要做的是刪除舊分區,！因此僅僅學會創建分區是不夠的！
　　刪除分區,，在Fdisk主菜單中選“3”后按回車鍵,。

FDISK Options

Current fixed disk drive:1

Choose one of the following:

1.    Create DOS partition or Logical DOS Drive

2.    Set active partition

3.    Delete partition or Logical DOS Drive

4.    Display partition information

Enter choice:[3]
　　 　　刪除分區的順序從下往上，即“非DOS分區”→“邏輯分區”→“擴展分區”→“主分區”,。
　　注意：除非你安裝了非Windows的操作系統,，否則一般不會產生非DOS分區。所以在此選先選“3”,。

Delete DOS partition or logical DOS Drive

Current fixed disk drive :1

Chose one of the following:

1.    Delete primary DOS Partition

2.    Delete Extended DOS Partition

3.    Delete Logical DOS Drive (s) in the Extended DOS Partition

4.    Delete Non-DOS Partition

Enter choice:[3]
　　輸入欲刪除的邏輯分區盤符,，按回車確定。

Delete Logical DOS Drive(s) in the Extended Partition

Volume Label Mbytes System Usage

5005 UNKNOWN    10%

43198 UNKNOWN    98%

Total Extended DOS Partition size is 48195 Mbytes (1 Mbytes = 1848576 bytes)

WARNING!  Date DOS in a deleted Logical DOS Drive will be lost.

What drive do you want to delete………………………………..?[ ]

Delete Logical DOS Drive(s) in the Extended Partition

Drv Volume Label Mbytes System Usage

D:                5005 UNKNOWN   10%

E,；              43198 UNKNOWN   90%

Total Extended DOS Partition size is 48195 Mbytes (1 Mbytes = 1848576 bytes)

WARNING!  Date DOS in a deleted Logical DOS Drive will be lost.

What drive do you want to delete………………………………..?[E]

　　敲入該分區的盤符（卷標）,，無則留空。

Delete Logical DOS Drive(s) in the Extended DOS Partition

Drv Volume Label Mbytes System Usage

D:                5005 UNKNOWN   10%

E:              43198 UNKNOWN   90%

Total Extended DOS Partition size is 48195 Mbytes (1 Mbytes = 1848576 bytes)

WARNING!  Date DOS in a deleted Logical DOS Drive will be lost.

What drive do you want to delete………………………………..?[E]
Enter Volume Label…………………………………?[            ]
　　按“Y”確認刪除,。

Delete Logical DOS Drive(s) in the Extended DOS Partition

Drv Volume Label Mbytes System Usage

D:                5005 UNKNOWN   10%

E:              43198 UNKNOWN   90%

Total Extended DOS Partition size is 48195 Mbytes (1 Mbytes = 1848576 bytes)

WARNING!  Date DOS in a deleted Logical DOS Drive will be lost.

What drive do you want to delete………………………………..?[E]
Enter Volume Label…………………………………?[            ]

Are you sure (Y/N)…………………………………?[N]
　　如是,，可將所有邏輯分區刪除。

Delete Logical DOS Drive(s) in the Extended DOS Partition

Drv Volume Label Mbytes System Usage

D: Drive deleted

E: Drive deleted

All Logical drives deleted in the Extended DOS Partition.

Delete Logical DOS Drive(s) in the Extended DOS Partition

No Logical drives defined

Drive letters have been changed or deleted
　　返回到主菜單,，再次選“3”,，預備刪除擴展分區。

Delete DOS partition or logical DOS Drive

Current fixed disk drive :1

Chose one of the following:

1.    Create  DOS Partition or Logical DOS Drive

2.    Set active partition

3.    Delete partition or Logical DOS Drive

4.    Display partition information

Enter choice:[3]
　　選“2”后回車,。

Delete DOS partition or logical DOS Drive

Current fixed disk drive :1

Choose one of the following:

1. Delete primary DOS Partition

2. Delete Extended DOS Partition

3. Delete Logical DOS Drive (s) in the Extended DOS Partition

4. Delete Non-DOS Partition

Enter choice:[2]
　　確認刪除,，按“Y”,。

Delete Extended DOS partition

Current fixed disk drive : 1

Partition Status type Volume Label Mbytes System Usage

C:1          A  PRI DOS            3004  UNKNOWN    6%

2             EXT DOS           48195            94%

Total disk space is 51199 Mbytes (1 Mbytes = 1848576 bytes)

WARNING ! Data in the deleted Extended DOS Partition will be lost.

Do you wish to continue (y/n)………………………[Y]
　　擴展分區已經刪除。

Delete Extended DOS partition

Current fixed disk drive : 1

Partition Status type Volume Label Mbytes System Usage

C:1          A  PRI DOS            3004  UNKNOWN    6%

Total disk space is 51199 Mbytes (1 Mbytes = 1848576 bytes)

WARNING ! Data in the deleted Extended DOS Partition will be lost.

Extended DOS Partition deleted

返回到主菜單,，依舊選“3”,。

FDISK Options

Current fixed disk drive :1

Chose one of the following:

1. Create  DOS Partition or Logical DOS Drive

2. Set active partition

3 .Delete partition or Logical DOS Drive

4. Display partition information

Enter choice:[3]
　　選“1”，刪除主分區,。

Delete DOS partition or logical DOS Drive

Current fixed disk drive :1

Choose one of the following:

1. Delete primary DOS Partition

2. Delete Extended DOS Partition

3. Delete Logical DOS Drive (s) in the Extended DOS Partition

4. Delete Non-DOS Partition

Enter choice:[1]

　　按“1”,，表示刪除第一個主分區。當有多個主分區時,，需要分別刪除,。

Delete Primary DOS Partition

Current fixed disk drive:1

Partition Status Type Volume Label Mbytes System Usage

C:1        A      PRI DOS          3004     UNKNOWN    6%

Total disk space is 51199 Mbytes  (1 Mbytes = 1848576 bytes)

WARNING! Date in the deleted Primary DOS Partition will be lost.

What primary  partition do you want to deleted..?[1]
　　按“Y”確認刪除。

Delete Primary DOS Partition

Current fixed disk drive:1

Partition Status Type Volume Label Mbytes System Usage

C:1        A      PRI DOS          3004     UNKNOWN    6%

Total disk space is 51199 Mbytes  (1 Mbytes = 1848576 bytes)

WARNING! Date in the deleted Primary DOS Partition will be lost.

What primary  partition do you want to deleted..?[1]

Enter Volume Label………………………………………?[              ]

Are you sure (Y/N)………………………………………?[Y]

　　主分區已經刪除,。

Delete Primary DOS Partition

Current fixed disk drive:1

Total disk space is 51199 Mbytes (1 Mbytes = 1848576 bytes)

Primary DOS Partition deleted

　　重啟后操作生效,。

You MUST restart your system for your changes to take effect.

Any drives you have created or changed must be formatted

AFTER you restart.

Shut down Windows before restarting.